|
|
Home > Assembly Instructions
| | |
|
| |
|
|
Print View
XP Assembly Instructions
|
|
|
Click here for a picture of
electrical outlet placement
Click here for
a picture of ideal in-room bed placement
|
|
|
1A.Remove lounge from
box. Place lounge, bulbs facing down, on a soft
surface. Remove the eight 5/16" x 1 " bolts from the
bench panel.
1B. Attach legs to lounge.
|
|
| |
1B.Remove the 42" x
16" pieces of styrofoam from the box and place them across
the bench rails (or use 2x4's). Remove the clevis pins
from the pistons. Attach the pistons to the ball stud
at each end (the smaller shaft is attached to the bench).
See step #4
|
| |
1C.Attach front skirt
and side skirt. Side skirt installs behind front skirt
with the 8 screws provided (you should be able to see into
the slotted louvres). Turn bench over so it is
standing on the legs. CAUTION:
DO NOT REMOVE FOAM PROTECTING THE TIMER, AS THE BUTTONS MAY
TEAR WHEN TURNING THE BED OVER.
|
|
|
|
| |
2. Remove the
3/8" x 1" bolts from the ends of the lounge. Attach
hinge plates. Nylon washers go between the hinge and
the bed end cap.
|
|
| |
|
| |
|
3.Remove canopy from
the box. Remove the 3/8" x 1.5" bolts from the ends.
Place the canopyCAREFULLYon
the Styrofoam or 2x4's that you placed on the bench. Make sure you line
up the rails or the styrofoam will break.
Align the top hole of the hinge with the hole in the canopy.
Install the 3/8" bolt though the shoulder washer and
bushing. Tighten all bolts at this time.
|
|
| |
|
|
| |
4. Slowly raise
canopy, remove 2 x 4's and attach the large end of the
piston to the top ball stud. Canopy should stay in the
open position.
|
|
| |
5. Attach the
body fan at either end of the bench using the screws
provided. Plug the body fan into the receptacle
located beneath the bed. DO NOT
ATTEMPT TO PLUG ANY OTHER DEVICES INTO THESE RECEPTACLES.
|
| |
6. Remote time
port is located at the rear of the bed across from the
timer.
If you are not using a remote;
be sure that the plugs are attached to each other.
A) When using a remote timer
other than a
T-Max; remove the red jumper
wire from the removable section of the plug.
B) Install new timer wires
where the red jumper was located.
NOTE:Save the red jumper wire and tape to back of bed for future
use.
This unit is equipped with a
with a 24 volt solid state backup timer that cannot be
bypassed. The backup timer will shut down the
bed and is set for the maximum exposure.
7. Connect canopy
and bench cords together; white to white; and black to
black. Plug the power cord into the wall receptacle.
Turn bed on using the timer. Check to make sure all
lamps are lit.
|
.jpg)
|
.jpg)
|
|
(6A)
Jumper
Wire
|
(6B)
Jumper
Wire Removed, Remote Timer used in conjunction with
on board timer.
|
|
|
| |
|
|
| |
|
SAFETY
INSTRUCTIONS
This product has a polarized
plug (one end is wider than the other) . As a safety
feature, this plug will only fit in a polarized outlet one
way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a
qualified electrician (you may need to replace your outlet).
Never use with an extension cord unless plug can be fully
inserted.
Do not attempt
to defeat this feature.
|
|
| |
|
|
|
| |
| | |
|
|
|